Exploring Basic Plumbing When You Install a Bathtub

Check It Out

How do you actually feel on the subject of Installing A Bathtub?


Tools You Need to Install a New Bathtub
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is also a moderately challenging project. If the old tub is easily available, the project can move immediately; if you have to open a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will certainly require a helper to move out the old bathtub and embeded in the brand-new one. Ensure you have actually certified on your own for the work and also fit trying it. Rather than working with a specialist to take over a halfway-completed job, it is far better to consider employing one prior to you start. Chances are you may require a specialist plumber to make tube connections.
This article will help you set up a brand-new tub in your bathroom if you have actually currently bought a brand-new bathtub and don't require to change the setup of your previous water system pipelines.
Your devices and also material list must make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be rather troublesome because of the restricted gain access to that is commonly the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
    Before moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipelines.
    If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
    Next off, place the tap in the installing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Protect the tap in place with the maker given backnut. As soon as the faucet is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Installing the Bath tub


    Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
    The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level reads degree.
    To set up taps, fit all-time low of the furthest flexible faucet connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
    Turn on the water and check all joints and also new pipework for leaks as well as tighten them if needed. Fill up the bathtub and likewise examine the overflow electrical outlet and the regular outlet for leaks.
    Ultimately, repair the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait until the bath tub has been made use of at the very least when as this will settle it into its final placement.

    Planning for the Installation


    Firstly, the supporting framework supplied with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
    Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the provided washers.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now prepare to be fitted in its final setting.

    Tiling Around the Bathtub


    In the area where the bathroom satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, causing complications with moisture and also feasible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the tub is in use. The sealer can crack fairly very early if you do not take into consideration this movement prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently available on the marketplace. It is recommended to fit the tiles utilizing waterproof or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    As a devoted reader on Tools You Need to Install a New Bathtub , I thought sharing that excerpt was really useful. For those who enjoyed reading our blog posting if you please remember to share it. Thanks a lot for taking the time to read it.


    Preventative solutions offered.

    Leave a Reply

    Your email address will not be published. Required fields are marked *